🗊Презентация Введение в оптические транспортные сети OTN

Введение в оптические транспортные сети OTN Профессор В.Ю. Деарт

Передача трафика поверх сети SDH

Преимущества концепции OTN/OTH

Сводка Рекомендаций МСЭ-Т по оптическим транспортным сетям OTN

Электрический и оптический уровни OTN

Электро-оптический уровень OTN

Подуровни электро-оптического уровня OTN The electro-optical layer is composed of three functional sublayers: The client signal is mapped into the Optical Payload Unit (OPU) layer. The OPU path connects the client equipment in an end-to-end manner and is not changed inside the OTN. The OPU overhead specifies the structure of the payload signal. The Optical Data Unit (ODU) layer enables monitoring of the end-to-end OPU paths. It enables detection of faults and bit errors and tandem connection monitoring. This information can be used for protection switching purposes. The Optical Transport Unit (OTU) layer monitors bit errors and faults. It adds additional information for Forward Error Correction as well. The OTU is the last electrical layer. It covers the same network parts as the first optical layer described later on.

Структура соединения в сети OTN-OTH

Оптический уровень OTN

Подуровни оптического уровня OTN(1)

Подуровни оптического уровня OTN(2) Multiplexing several optical channels creates the Optical Multiplex Section (OMS) layer. It provides networking functionality for the transmission of a multi-wavelength optical signal. The OMS layer includes overhead information to monitor signal integrity and provide functions for operations and management, such as defect indications. This overhead is transmitted in the Optical Supervisory Channel (OSC) as well.

Подуровни оптического уровня OTN(3) The Optical Transmission Section (OTS) layer provides transport function for the OMS layer signal. There is a one-to-one mapping between both layers. The OTS defines the optical parameter of the physical interface such as: Frequency and power level. The optical transmission section layer includes overhead bytes for maintenance and management purposes, which are transmitted in the optical supervisory channel together with the overhead of the optical channel layer and optical multiplex layer.

Способы восстановления оптического сигнала

Пример оптической транспортной сети OTN

Организация участков оптической транспортной сети (1) The client access (CA) equipment mappes the client signal, e.g. an STM-N signal or Ethernet, into the OPU and creates the OTH signal. This signal is transmitted through the OTN and terminated at client access equipment. To cover long distances optical line amplifiers (OLA) are used to amplify the optical signal. Optical cross connects or optical add/drop multiplexers are used to switch the optical channels between different ports. To switch a single ODU signal, which is an electrical layer, it’s necessary to terminate higher levels of the signal. This requires optical-electrical conversion, including 3R regeneration. For this operation an electrical ODU cross connect can be used. After switching the ODU, an electrical-to-optical conversion is performed to build the optical OTS signal. The optical transmission section OTS with its associated overhead is terminated at each network element.

Организация участков оптической транспортной сети (2) The optical transmission section OTS with its associated overhead is terminated at each network element. Optical cross connects or optical add-drop multiplexers switch on optical level only. They do not perform optical-electrical-optical conversion. Therefore only the OMS needs to be terminated. If an optical-electrical conversion has to be performed, the complete optical section has to be terminated, including the optical channel and OTU path using Electrical ODU cross connect

Размещение клиентского сигнала и мультиплексирование оптических каналов

Электро-оптические уровни OTN The client traffic is mapped into the payload area and the overhead bytes are added. This results in the Optical Payload Unit (OPU). The next layer is based on the OPU: To the OPU, overhead bytes and bytes for Tandem Connection Monitoring (TCM) are added to built the Optical Data Unit (ODU). The ODU together with overhead bytes and bytes for Forward Error Correction (FEC) represent the Optical Transmission Unit (OTU), the last electrical layer. The OTU is then converted into an optical channel of a specific wavelength. Several wavelengths are multiplexed.

Секция мультиплексирования OMS и секция передачи OTS Additional overhead bytes for each optical channel are added. They are not transmitted on the same wavelength as the optical channel. This additional channel is called the Optical Supervisory Channel (OSC). The optical channels together with additional overhead bytes built the Optical Multiplex Section (OMS). The overhead bytes are transmitted in the OSC as well. For the Optical Transmission Section (OTS) overhead bytes are added again. They are transmitted in the OSC also. In the OSC additional OTM communication channels are transmitted for management purposes.

Оптические транспортные модули(1)

Оптические транспортные модули(1)

Структуры транспортных модулей(1)

Структуры транспортных модулей(2)

Схема мультиплексирования OTM

Структура мультиплексирования OTU

Передача кадров в OTH

Структура кадра OTH

Структура заголовка OTUk(1)

Структура заголовка OTUk(2)

Структура заголовка OTUk(3)

Структура заголовка ODU (1)

Структура заголовка ODU (2)

Структура заголовка OPU

Уровни контроля модемных соединений ТСМ

Проверочное поле FEC

Размещение кодовых слов RS в кадре OTH